Timber Cladding Fitting Instructions

Timber Cladding Fitting Instructions

Timber Cladding Fitting Instructions

Timber Cladding Installation Instructions Timber Focus

Timber Cladding Fitting Instructions

We are leading suppliers of Timber Cladding  in our range we supply;

  • Siberian Larch selected for  Heartwood only,
  • Painted Timber Cladding, profiles, featheredge
  • Fire Retardant Cladding,
  • Thermowood Cladding,
  • Spruce Whitewood Cladding,
  • Redwood Pine Cladding,
  • Western Red Cedar Cladding,
  • Sweet Chestnut Cladding,
  • European Oak Cladding,
  • Accoya Cladding,
  • Sapele Utile Cladding
  • Ayous Cladding
  • Andira Cladding
  • Iroko Cladding
  • Scottish Larch Cladding etc
Black Painted Cladding
Black Painted Cladding

We can supply the cladding in various patterns or designs such as sawn to size, machined to profile  Square edge, Shiplap, tongue and groove, board on board, rainscreen or waney edge etc. We value sustainability, and we are FSC, and PEFC Certified we aim to supply all our products from sustainable sources.


We provide Cladding specification and samples service for any timber cladding project as a free service nationwide. We provide support both external wall cladding and internal cladding.


External Timber Cladding Installation Instructions. We strongly recommend that Qualified Professionals undertake the installation of our cladding products.


Membranes to be used on all rainscreen cladding

  • UV Facade membrane to be used on open jointed cladding.
  • Normal BBA approved breathable membrane to be used on closed rainscreen cladding.

Insect Mesh · Install Insect mesh around all open cavities.

Timber Cladding Support Battens

  • All battens to be treated to UC3, all cut ends to be treated on site.
  • Vertical cladding to be supported with 45x45mm treated battens with a minimum 15

degree slope.

  • Horizontal battens to be minimum 38x50mm. · Recommended spacing of battens should

be 450mm centres and not exceed 600mm centres.

  • Ensure sufficient space behind the cladding for ventilation and drainage.


  • Stainless Steel fixings type 304, or 316 near coastal areas.
  • All nails to be annular ring shanks, minimum 50mm for 16-20mm thick board, or the nail

length to achieve a point side penetration of 2 ½ times the thickness of the cladding board

into the batten.

  • Minimum 2 face fixings required for boards up to 150mm wide and additional fixings for

wider sections. We recommend maximum board widths of 150mm to reduce overall

shrinkage or swelling.

  • Fix nails or screws approx. 20mm from the end and edge, avoiding splitting of the boards.

Some timbers require pre-drilling, refer to CE Marking and DOP – downloadable copies are

available on our website.

  • Do not secret fix through the tongue or groove. · All fixings to lay flush with the surface of

the cladding.

  • Fix the cladding, ideally, at 450mm maximum centres.

Board Configuration and Layout

  • For horizontal rainscreen the Grooves need to be to the bottom to minimise the collection of water or pollutants.
  • Vertical Claddings need to be chamfered at the ends for drainage into the cavity.
  • Minimum 2mm gaps should be left around the boards for expansion, larger gaps to be left

for differential movement, especially in timber frame constructions.

  • Allow between 6mm to 10mm for drainage gaps on corner profiles, ends, sides or other

materials (check the compatibility of the cladding with other materials in the construction,

to avoid/minimise corrosion and staining).

  • Cladding to be installed at least 250mm above ground level.
  • Store cladding away from direct sunlight, rain etc before installation or during acclimatising to minimise the risk of splitting, checking or distortion.

Finger-Jointed Cladding All finger jointed cladding is not supplied for load bearing, please ensure an external quality coating is applied and maintained to ensure you achieve optimum service life from the glue lines.

Waney Edge Cladding We recommend treatment for waney edged cladding due to the presence of bark and sap if ordered untreated.


Siberian Larch Decking and Cladding Timber Focus
Siberian Larch Decking and Cladding Timber Focus
External Fire Retardant Treated Timber cladding Euro Class B BS EN13501-1 Opaque White sample 1 Textured sawn face secret fix concealed profile Timber Focus
External Fire Retardant Treated Timber cladding Euro Class B BS EN13501-1 Opaque White sample 1 Textured sawn face secret fix concealed profile Timber Focus

Factory Finished / Coated Claddings

Always keep separating membranes between the layers during handling and transit to protect damage to the lacquer and sticking to surfaces. It is important to follow applied product manufactures guidelines due to the large variety of finishes, coatings and treatments available.

Ensure all edges and sides are sealed prior to installation, including any fixing holes.

All factory finished products need minimum annual maintenance i.e. to clean surfaces any pollutants moreover touch up for any degradation.


General Maintenance Comments Timber will weather, oxidise and is susceptible to fungal / mould staining if unprotected or untreated, changing the aesthetics of the timber. During the early weathering process the timber surface may also show signs of variations in colour, which should gradually even out, this depends on exposure. Colour variation in wood is an inherent characteristic of wood i.e. Between and within board variation of colour should be expected in wood. We provide a sample service upon request to help in the selection of cladding species. Annual maintenance is recommended; i.e. basic care and maintenance for uncoated or untreated wood, depending on the type of pollution present, would be to wash off with water (do not flood), or sand it off. Bleaching can also be used to help remove stains. The above are general guidelines but cover some of the key aspects, as every project needs to be considered individually. All products offered above are available from Timber Focus and, for detailed timber cladding fitting instructions, copies of BM TRADAs External Timber Cladding installation manual are available to purchase from Timber Focus. Please feel free to download our cladding brochure from the downloads section of our website at https://www.timberfocus.com/downloads/


For  more information contact us


Timber Focus Ltd  / Puidukoda (HEAD OFFICE)  

3000 Aviator Way
Manchester Business Park
M22 5TG

Tel:  0161 504 0011        
 0161 240 3611


Email: info@timberfocus.com


Please note we are experiencing delivery delays on orders due to increased demand and COVID-19.

However, we are still processing all orders as fast as we can.